PlanetZ forums - scopeusers.com

Maybe - you know if it's possible to disable?

With the 1.0.2 update off NI's Kore controller, xtc plugs load and actually SOUND :smile:
But :sad: the program crashes after some playing (B-2003 only plug tested)

Has anyone tried this with different results?

If so - got any "magic tweaks" to share?

<font size=-1>[ This Message was edited by ...

Thinking about getting an extra card(Pulsar2), to get the extra ADAT ports. Already have PowerPulsar and using ADAT-port on that card. Anyone know if it's possible to link cards via TDM and use both cards ADAT ports (different no of DSP matter?) ?

Got it! Newbie found the answer himself...
For other newbies:
Multi program change on same channel as set for mixer/aux. Haven't found a way to change bank numbering yet though, but that's really not crusial either...

I tried changing presets in multi mode via program change/bank change in Cubase SX. Problem is bank change doesn't seem to work at all. Program change switches only presets in Factory bank(#0) for a "slot", EVEN IF another bank (say #1) is the currently selected for that "slot". Problem remains even ...

Thanx for info

Hi. I'm thinking of selling my PowerPulsar and buying Noah EX, since I almost exclusively do live-gigs. I know it's possible to use for ex B2003 and Minimax simultaneously in N-EX. Is this "multi-setting" stored in a preset, so you can switch between "multi-setups" with midi program change messages ...

Very very useful indeed. I use SFP for live playing so this kind of device would great! Hopefully not to hard to do on your own when (if) SDK goes public.

I'm trying to use the STS like a multi-timbral synth for live play:
For each separate song - Load a number of sample progams in a number of slots of the sts, say slots 1 to 5, on different midi channels like a multi-timbral synth. I also want to use different volume and pan settings for each such ...

...just det ja! Så klart det inte går. Det var ju i och för sig bra att dom hittat ett fungerande skydd, men dyrt :wink:

<font size=-1>[ This Message was edited by: zoofar on 2003-08-26 16:44 ]</font>

<font size=-1>[ This Message was edited by: zoofar on 2003-08-26 16:45 ]</font>

I'm currently using PowerPulsar, Z-link, A16 Ultra. Was thinking of expanding with an affordable 8ch pre-amp (Behringer ADA8000...yes I know) for recording live acts. Would ADAT in/out on the preamp be all needed for a 16+8 channel setup to work? Anyone with experience from this?

I tried 2448, micromixer and DynamicMixer, and they all respond to MIDI program change messages, but not the 1632. Anyone else have this problem?

Hi.
I'm thinking about adding some softsynths to my PowerPulsar system. Any opinions on the Vectron and Minimax? Is the difference big from VectronPlayer and Miniscope? How about from other included synths?
Basically - Do you think they raise a system by "at least as much as they cost"?
Will ...

Yes it does indeed!
That's infact exactly what I would need to complete my live-setup-case. Good tip!

Do you think line boxes would do the trick? As mentioned, it's only for live use, and my main goal is to reduce noise to a level acceptable at live performance, where noise is pretty high anyway. Then again I can always try instead of keep asking

From what I've learned ; When the ScopeCard get's it's "turn" to use the CPU for specified amount of guaranteed time (ms or cycles don't know), this is the only time that SFP-software can actually communicate with SFP-hardware. When the time is up, interrupt controller on motherboard passes the bus ...

Thanx. Always nice to know you're normal

Follow up question:

I frequently use my system for live playing, and I usually have need for everything from 1 to 10 mic's . Is there a budget-quality multi-channel pre-amp out there ( say 300-400$ or so ), or might I just as well buy a cheap mixer?

When using A16 ultra & Z-links, it's impossible to get a clean Mic-signal. This is the chain:
Mic SureBeta58 -> balanced in A16 Ultra
If using -10dB the nosie:signal ratio is a little better than using +4dB, but not by far comparable to when using a preamp of some sort between mic and A16 ( like a ...

I'm using PowerPulsar for live playing, and I'm trying to figure out a way to set Delay tempo of some SFP FX with an external footswitch. Has a anyone got any ideas? Would be nice for setting vocal delay times live.

(I have access to Cubase SX if that would be a useful tool...)

One specific "problem" that changing PCI latency solved on my system:
When playing CW synths via external MIDI keyboard ( MIDIsport 4x4, USB ( i.e PCI ) ) moving a controller for say modulation or volume quickly would send more MIDI-messages than ScopeCard could handle ( or PCI-bus rather ), and so ...