Decimator... irritating noise

Micronesia · Post by **Micronesia** » Mon Feb 06, 2006 3:40 am

When i open it i get a horrible loud pop!!!
Is this professional?

- Get Creamware Scope - the system that requires you to turn down the monitor volume when opening new FX units!

GAHonGHA!

fra77x · Post by **fra77x** » Mon Feb 06, 2006 3:58 am

It;s your systems fault. I doubt you 'll ever fix it... Now go by something PRo.

[ This Message was edited by: fra77x on 2006-02-06 03:59 ]

Post by **garyb** » Mon Feb 06, 2006 9:28 am

this is mentioned in the manual, which you should read..and stop whining...

Micronesia · Post by **Micronesia** » Tue Feb 07, 2006 2:13 am

I checked the effects manual on decimator, says nothing.
Please refer to the document or page..

djmicron · Post by **djmicron** » Tue Feb 07, 2006 3:04 am

micronesia, what do you mean?
I open the decimator without problems....

symbiote · Post by **symbiote** » Tue Feb 07, 2006 4:03 am

I don't get noise when I load it as an insert either, even when there's sound playing on the channel (STM2448 mixer.)

I think garyb meant manual more as in "general troubleshooting" section than the actual decimator/effects manual.

Post by **garyb** » Tue Feb 07, 2006 1:58 pm

nah, my mistake!
i misunderstood. i thought your problem was on startup of the system. i've never had a problem with the decimator making a pop....the graphic eq does though, so i turn down the monitors when opening that plugin. i wish i had a good solution for you....

wayne · Post by **wayne** » Tue Feb 07, 2006 5:56 pm

Yep, GraphEQ is the only one that does that here.

Do both mono and stereo versions pop?

May be a corrupt dev.

[ This Message was edited by: wayne on 2006-02-07 17:59 ]

Booster · Post by **Booster** » Tue Feb 07, 2006 11:43 pm

GraphEQ popping? Deciminator popping? I don't have any effect popping when opening it?!

marcuspocus · Post by **marcuspocus** » Wed Feb 08, 2006 11:31 am

try inserting grapheq31 on a master channel when audio is playing

And... what your ears/speakers

Booster · Post by **Booster** » Wed Feb 08, 2006 11:40 am

On 2006-02-08 11:31, marcuspocus wrote:
try inserting grapheq31 on a master channel when audio is playing

I am! No popping, no noise, just a short mute.

What am I doing right?

petal · Post by **petal** » Wed Feb 08, 2006 2:07 pm

I have that popping too - would like to find a solution for it.... Strange that only some systems have it!?

Mr Arkadin · Post by **Mr Arkadin** » Wed Feb 08, 2006 2:11 pm

Mind you i always think it's foolhardy to insert anything (even hardware) whilst something is playing - you never know what might happen.

[ This Message was edited by: Mr Arkadin on 2006-02-08 14:12 ]

petal · Post by **petal** » Wed Feb 08, 2006 3:12 pm

I like living on the edge....

Micronesia · Post by **Micronesia** » Thu Feb 09, 2006 1:12 am

I do get a loud incredibly annoying and sometimes scary *zzchhAA-POp!!!!* each time i open the Decimator and both the EQ you mention.
Wierd that some has it and some dont.. Then its about a compability problems.

samplaire · Post by **samplaire** » Thu Feb 09, 2006 1:21 am

Maybe different ulli setting and different asio modules. There may be many factors to be responsible for that behaviour.

For instance, my friend has pops when stopping/starting playing in Logic while I don't have any. In this case our systems differ much (different audio hardware). But this doesn't lead me to any conclusion like pro or no pro...

Micronesia · Post by **Micronesia** » Thu Feb 09, 2006 1:36 am

I can tell you this, i use samplerate 48khz with Scope as master.

No asio modules are active, i am using another soundcard for that. The Scope only acts as a hardware mixer/effect/synth device...
The only communication is via the Virutal Midi drivers & Adat out & in.