using XTC with diff i/o than CW

digbob · Post by **digbob** » Thu Sep 16, 2004 3:53 am

Hi
i want to use XTC in Nuendo 2 but i need to use the i/o of a RME Card, how can i use XTC mode with a diff. Asio Driver
thanks for any Help
dany

Post by **garyb** » Thu Sep 16, 2004 11:22 am

Eric Dahlberg · Post by **Eric Dahlberg** » Thu Sep 16, 2004 11:27 am

Is this true even when using an SRB instead of a full Pulsar with i/o's? Weren't the original XTC cards just SRB's, anyway?

Post by **garyb** » Thu Sep 16, 2004 11:52 am

yes, if using a no i/o card(a plug is available from cw for removing the i/o plate), you can use xtc with the rme, but with a stock card, no.

this seems kinda redundant, since the rme has no real advantage, but whatever makes your system work....

Eric Dahlberg · Post by **Eric Dahlberg** » Fri Sep 17, 2004 11:00 pm

Gary, do you think I could get you to try it with my SRB/XTC board? I've really had no luck getting it to work so far & figured that it just wasn't going to work.

Post by **garyb** » Sat Sep 18, 2004 3:24 am

sure...

Quifster · Post by **Quifster** » Sat Sep 18, 2004 1:08 pm

with scope 4.0 there is a program called scope i/o enabler/disabler.

as far as i know, you can use this one to disable the io plate of your pulsar, scope card.

that should do the trick.

Chris · Post by **Chris** » Sun Sep 26, 2004 11:02 pm

Hey Guys,

I too would like to use XTC mode with another I/O card (Yamaha 01x)

I tried the IO enabler program and no luck - Any other tips. Do you need a special project ? I assume you need to start Scope prior to starting Cubase.

Thanks

devastate · Post by **devastate** » Sat Oct 16, 2004 6:03 am

have you tried putting a soundcard dest module into your xtc project? I've done this messing around with other soundcards to see how the output sound was different to my scope i/o's. Just remember to make one card a master and one card a slave and you shouldn't have any problems. With regards to a delta 10/10 i'd presume you would have to have a number of soundcard source/dests to set it up for multiple i/o. This still uses the scope asio and gives you access to other cards. Can't guarantee it'll work in all circumstances but it worked for me.

siberiansun · Post by **siberiansun** » Sun Oct 17, 2004 6:29 pm

On 2004-09-27 00:02, Chris wrote:
Hey Guys,

I too would like to use XTC mode with another I/O card (Yamaha 01x)

I tried the IO enabler program and no luck - Any other tips. Do you need a special project ? I assume you need to start Scope prior to starting Cubase.

Thanks

so you tried this in ver 4.0?
please let me know if you've found a solution as i've just ordered an RME card and i still would like to hold on to the Optimaster and the Masterverb..

eliche · Post by **eliche** » Fri Oct 21, 2005 2:51 am

I have a pulsar XTC Pro, with Classic IO and a Yamaha 01x. With or without disable I/O with IO Enabler of SPF4, i have noticed that some module like masterverb and some synths like bluesynth have no problem to run in XTC mode with my ASIO M-LAN driver active, but some other, like compressor, generate noise and crash of the system