micromixer x - modular

[djmicron]

This one is a test before adapting the bigger ones.

When channels are in mono mode, only left input is active.

micromixmod.jpg (177.95 KiB) Viewed 3262 times

[jksuperstar]

Wow, now THIS is VERY useful My thanks for your willingness to do this. I imagine the possibilities will only be better with Open SCOPE 6 (as S|C hints one would be able to incorporate an extra LFO into a MiniMAX for example, or make a new GUI for it).

This is very cool, thanks, DJM!

[dawman]

I always liked Modular Shell Mixers.
Hopefully this is just a start, and the STM1632X or a mixer with at least 2 AUXs would be added later.
I'd love a Project window full of Modular Shells where little room is used.
THen have Screensets for each combination of devices and Modular shells to be viewed.

Thanks Again DJM..

[faxinadu]

yeaaaaaaah! does this require scope5/mod4?

[djmicron]

it works in any modular version, but it requires scope 5 due to different serials between v5 and v4 devices.

If you have scope 4, drop me a message

[Bud Weiser]

it works in any modular version, but it requires scope 5 due to different serials between v5 and v4 devices.

If you have scope 4, drop me a message

Scope 5.1 and 4.0 here,- on different machines ...

Does that mean there´s a solution for both the versions ???
That would be amazing.

O.T.:
I have a Scope 4.5 installer too and wonder if there were Scope 4.5 keys needed or if Scope 4.5 works w/ v4.0 keys ?

Bud

[djmicron]

v 4 and v4.5 should be the same keys(if i remember right).

I can pack the device on sdk 4 with the old version of the devices, then it will run on v 4.

[Bud Weiser]

v 4 and v4.5 should be the same keys(if i remember right).

I can pack the device on sdk 4 with the old version of the devices, then it will run on v 4.

Cool, thx !
Minimax possible too ?

I don´t have B2003 and Profit 5 for v4.x, - but Minimax (+ Prodyssey and 4 ZARG synths).

The idea is, running Modular III (and occasionally STS sampler) only on the Scope v4.x / 15DSP PCI card machine, connected by ADAT I/O and MIDI to XITE-1.
I expect it helps running devices not being optimized for XITE like STS samplers and/or running more devices when XITE is at it´s DSP load and SAT connection limits.
Just a workaround until Scope 6 (or higher versions) will be released ...

Bud

[djmicron]

i miss the prodissey, but most of the rest is possible, including minimax.

v 4 and v4.5 should be the same keys(if i remember right).

I can pack the device on sdk 4 with the old version of the devices, then it will run on v 4.

Cool, thx !
Minimax possible too ?

I don´t have B2003 and Profit 5 for v4.x, - but Minimax (+ Prodyssey and 4 ZARG synths).

The idea is, running Modular III (and occasionally STS sampler) only on the Scope v4.x / 15DSP PCI card machine, connected by ADAT I/O and MIDI to XITE-1.
I expect it helps running devices not being optimized for XITE like STS samplers and/or running more devices when XITE is at it´s DSP load and SAT connection limits.
Just a workaround until Scope 6 (or higher versions) will be released ...

Bud